- Offizieller Beitrag
Wie macht ihr die Abschaltung von dem Hammer? Nur per hand oder elektronisch / Endschalter?
Wie macht ihr die Abschaltung von dem Hammer? Nur per hand oder elektronisch / Endschalter?
Eye/hand coordination at the moment.
Your special edition with wired connections (silicon wires): ready for transport.
Solved.
Solved.
Danke für den vorherigen Hinweis. Der Upload von dem Bild hatte zeitlich etwas länger gedauert.
Toll, endlich wieder ein Axtbot in der Arena. Man sieht auch schön die Handschrift und die Erfahrung von Leo und Mario. Antriebsaufhängung, Form der Panzerung, Reifen, etc.
Sierht esch toll aus! Mir fehlt nur die "alte" Kashei-Form!
Ja, sehr schön geworden. Sieht auch absolut stabil aus.
Beeindruckt bin ich, dass seitlich am Axt-Zahnrad die seitlichen Schutzkrägen in "rund" angefertigt sind. Habt ihr es geschafft, das Hardox zu fräsen? Oder gibt es einen anderen Trick für das Anfertigen von runden Teilen aus Hardox? (Ok, Wasserstrahlschneider.... aber so etwas habt ihr doch nicht, oder?)
Aus der hand gemacht mit ein Plasmabrenner.
Läuft wirklich sehr stabil. Vor allem bin ich beeindruckt, dass der Waffenarm immer korrekt stoppt, ohne den eigenen Bot zu beschädigen. (Ihr habe keine Endlagenschalter verbaut, so wie ich das verstanden habe.)
O.o.t.:
Es ist offensichtlich eine sehr ruhige Gegend, wo ihr testet. Kein einziges Auto, das auf der Straße fährt. Kein Nachbar, der sich beschwert..... Und auf der Straße ist kein einziger Kieselstein, der die Fahrt des Bots behindert. => Schöne Gegend!
Kashei Besmertnye.
Current weight 11.5kg
Drives.
Ranglebox Neptunes. 28.4-1 planetary gearbox, a replacement for the GR02. 100mm RC wheels.
ESC, IBF 4.5
Weapon. 30-1 3 stage spur gear gearbox mated with a NTM 5060 370 KV motor and TZ85a with SimonK software.
Battery Zippy 4 or 5S 5000mAh LiPo
RX/TX
Turnigy TGY i6 TX , mated with telemetry modules for temperature and voltage. (measuring NTM temp and battery voltage)
Armor,
Sides all angled 3.2mm Hardox 450 with stainless steel ribs.
Top and bottom 5 -12mm HDPE
Last weekend brought us FACTS. A 45K+ visiters Comic con weekend.
Teal RCC entered 3+2 machines. The 3 machines were Hannibalito3, Kashei and Perun.
The +2 are the new machines build for others. Robotus Vulgaris and the Unnamed (Hannibalito3/Brobot/Scotbot clone)
Just an overview of 4 of'm, as Unnamed was used by the new owner.
Hannibalito3 went into the fire. First fight, Full on spinner combat against the brandspankingnew monsterdrumspinner Equinox.
It was just gruesome, horrible. HDPE chips splattering around like blood from the stump of a severed limb. The flipperarm got a new shape Piccaso would drool upon.
After that fight, replacing the flipperarm with the spare, and hacking off some ripped HDPE to make it a bit safer to handle. A fast checkover didn't reveal any other damage. Unfortunatly, it was a fast checkover, and we failed to do a pressure test.
Next fight, a massive leak in the CO2 setup was detected.
With a limp flipper, only Leo's expert driving gave us the win.
Workbench, some skullsweat and a replacement Burkert and the leak was history.
After this, H3 was itself.
In the arena, fight, out the arena, replace CO2 bottle and battery, ready.
Kashei Besmertnye.
It looked so good, but after 2 fights, the axe failed. Mod 2 gears just lost teeth.
Removed the axe, and used it as a decent rammer.
Drives are fine, so it did the job.
Perun, the persistent one.
It exactly did where it was build for. Go in the arena, bulldozer the opponents into the wall. Rince and repeat.
Only wear and tear got 1 of the gearboxes of the GR02 drive. Replacement mounted and ready to rock again.
Robotus Vulgaris. A BonX/Hardwired2 clone.
The maiden trip.
Equinox again. But the armox/hardox armor held fine, some deep scratches and that was it.
Equinox's weapon sheared some bolts and needed a lot more attention.
Next fight was against Valkiri3 Pyro. And that was a nasty surprise.
The disk can cut 5mm thick armox 600, not like butter, but nontheless as if a 12mm mill was punched trough it. One of the horns was ripped off and the drive-coverplate looks like it was used a doggies chew-toy.
One of the Saturn motors doesn't have magnets anymore, but adhesive powder.
This more needs more than a bit TLC and upgrades before it goes to the new owner.
I have to admit. On Saturday, I spend more time oogling the eyecandy (a few dozen nicely shaped Suicide Squad Harley Quins and other cosplaying beauties do that to a normal man) than working on the robots.
Sunday was my "drop dead" day, and I slept like a dog in a basket under a workbench.
And now, The upgrade/repair of Vulgaris.
Neither did we, Mercury did way more damage than I thought possible.
Mercury is still called Valkiri, that was just some missunderstanding.
I think I found out why one of the drivemotors burnt out. I guess some metal flakes got inside the motor when drilling the new holes for the weapons motor...
I did not recognize that the tape came of the motor.
Hannibalito 3 hat ein neue look bekommen, wie zu sehen auf MMM in Dortmund. Das waffe ist immer noch das gleiche wie vorher.
Wir hatten kleine aber bestimmte problemen die wir lösen mussten, z.b. die selbst auszeihende link in Kashei, und problemen mit der sicheruning in der IBF fahrtregler in H3. Dass sind sachen die wir erledigen vohr die nächste kämpfe.
problemen mit der sicheruning in der IBF fahrtregler in H3. Dass sind sachen die wir erledigen vohr die nächste kämpfe.
Ich werde bei dem Thread von dem Fahrtregler ein paar Empfehlungen hinterlegen, wie die Sicherung bzw. der Sicherungshalter ausgetauscht werden kann. (=> Wir hatten das schon besprochen. Aber ich möchte vermeiden, dass ihr einen "minderwertigen" Sicherungshalter bestellt)
Mit eurem neuen Design hatte ich mich schon etwas gewundert. Früher war H3 "nur" HDPE, jetzt mit Hardox-Untetstützung.
Ich denke nicht das der Hardox mehr spinnergewalt haltet dann vorher mit rein HDPE, aber zu mindest schutzt es die CO2 flasche besser und mir gefallt der blaue farbe.